RC-Monster Forums
Page 10 of 10 « First 89 10
Show 40 post(s) from this thread on one page

RC-Monster Forums (https://www.rc-monster.com/forum/index.php)
-   Brushless (https://www.rc-monster.com/forum/forumdisplay.php?f=12)
-   -   Project High Voltage (https://www.rc-monster.com/forum/showthread.php?t=4777)

BrianG 05.17.2007 08:44 PM
Yikes CHC! That's an expensive display of smoke! BK should provide an insurance policy for their controllers me thinks...

jhautz 05.17.2007 11:05 PM
I say Mike should stop selling BK until they make this right for you!!!


Oh... wait.... He did that already.

neweuser 05.18.2007 09:00 AM
Quote:
Originally Posted by coolhandcountry
I have had the problem with this esc since i got it. It has even been back
to bk to get repaired. They said it was ok and updated the software.
I have been in a debate in emails with them over the esc not working like it
should. They trying to put it off on user error. The controler popped smoked.
It was sending constant electric thru the motor and smoked the motor.
May as well say about 800 bucks poof up in smoke.
All I got to say is Thanks BK!!!:036:
Well, they did the same to me with my 12020. I contacted the better business bureau after several emails, they finally said they would replace it, still have not seen teh esc yet though. This was last month.

suicideneil 05.18.2007 10:33 AM
BK = Bloody Kon-artists. Its not good, not good at all when you spend all your money with one company, expecting them to help you out if something unexpected happens, only for them to say "your fault".

neweuser 05.18.2007 10:44 AM
I agree, the sad thing is, not all their product is "bad" or whatever, and they have been around for some time, so you would think one could get SOME customer service after spending 800.00!!!!

Procharged5.0 05.18.2007 12:18 PM
That's just not right! Hope BK does something stand-up to take care of you.

GriffinRU 05.18.2007 02:00 PM
Leroy, sorry to hear that. I can take a look on your second controller :) maybe I can put smoke back...
And what happen with motor?

aqwut 05.21.2007 10:08 AM
That Really sucks dude... you're out more then me when my 2280 toasted...

coolhandcountry 05.23.2007 10:32 AM
Quote:
Originally Posted by GriffinRU
Leroy, sorry to hear that. I can take a look on your second controller :) maybe I can put smoke back...
And what happen with motor?
From what I seen Artur. The esc got stuck on one phase. It sent all the volts and amps thru one phase of motor. It cooked the windings and solder off motor. It had a serious melt down. The epoxy melted and stuck to rotor in motor. I had to use pliers to even get the rotor to spin. It burnt a few in pieces. :002: The motor let off more smoke than esc did. I haven't heard nothing from BK. To me BK=Big Krap now. It is still same esc that I sent to them. They updated the software and said nothing was wrong. It works much better cool than hot. As it got warmer it got worse and worse.

I would like for them to give me a good esc. That is all I ask. Then I can sell it on ebay. :D

neweuser 05.23.2007 10:34 AM
Sorry to hear your issues CHC. Keep at BK even if you need to call them. It took me awhile until they finally responded.

GriffinRU 06.02.2007 11:36 PM
Quote:
Originally Posted by coolhandcountry
From what I seen Artur. The esc got stuck on one phase. It sent all the volts and amps thru one phase of motor. It cooked the windings and solder off motor. It had a serious melt down. The epoxy melted and stuck to rotor in motor. I had to use pliers to even get the rotor to spin. It burnt a few in pieces. :002: The motor let off more smoke than esc did. I haven't heard nothing from BK. To me BK=Big Krap now. It is still same esc that I sent to them. They updated the software and said nothing was wrong. It works much better cool than hot. As it got warmer it got worse and worse.

I would like for them to give me a good esc. That is all I ask. Then I can sell it on ebay. :D
Can you take a picture of LEHNER iron core?

coolhandcountry 06.03.2007 11:28 AM
I have junked the motor. I had to use pliers to get rotor out of case.
I got rotor still. :D I may as well have something for my 300 bucks.

GriffinRU 06.03.2007 11:59 AM
Quote:
Originally Posted by coolhandcountry
I have junked the motor. I had to use pliers to get rotor out of case.
I got rotor still. :D I may as well have something for my 300 bucks.
You can use magnet on the fridge, I bet it is much stronger then Novak's you used to have on it :)
I just recently ripped apart Feigao can and now it is clear why their specs are so broad and efficiency sucks, so I thought it would be nice to take a look on Lehner core while we have seen neumotors core from their website.

coolhandcountry 06.03.2007 01:37 PM
I use them for a nice screw holders.
Yeah it is pretty strong. I got a pic on here some where the inside of a
lehner motor. The wires are alot straighter in the can. Don't have the
S configuration like in the nemisis or feigaos.

coolhandcountry 11.06.2009 03:35 PM
This truck is now part of an on going project truck.
More to come at later date. :smile:


All times are GMT -4. The time now is 06:04 AM.
Page 10 of 10 « First 89 10
Show 40 post(s) from this thread on one page

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2025, vBulletin Solutions Inc.