Do you have a link to the trays?

http://www.amainhobbies.com/product_...ducts_id/21719

There you go just needs straps

Thanks.

Happy Ho Ho
 

Wow, great xmas...

this is what i got :
http://i152.photobucket.com/albums/s...E/PICT0096.jpg




Old servo..
http://i152.photobucket.com/albums/s...h_PICT0107.jpg




Ds 1015
http://i152.photobucket.com/albums/s...h_PICT0108.jpg




Wiring Etc
Im swapping over to all Ec5 connectors- i love them, soo much easier to soder then deans-dont require heatshrink if done right and offer a bit more surface area to pull them apart... the only thing is that the connectors housings are easy to mix up.... My entire setup is flip-flopped...:whistle:
Made a simple series harness out of excess wire from my MMM- i can easily swap it out for a deans pug or whatever I may need.

RCM-lipos
WOW!:surprised: These packs have some balls! 145amps of continuous goodness... soo much power that my diff case seperated from wheelies.... after a cleanup and a rebuild i was at it again. These packs are night and day difference compared to my zippies- the only con is that they are heavier.:neutral:

very nice ben!!

Thanks trev.. also got a new wing! makes the truck look pretty:)


One quirk i have found with the RCM 2s's is the not-so-standard thunderpower balance tap, I ended up taking the indidual connectors our of the TP housing and pluging them into my charger/balancer manually..

http://i152.photobucket.com/albums/s...E/PICT0109.jpg
http://i152.photobucket.com/albums/s...E/PICT0113.jpg
http://i152.photobucket.com/albums/s...E/PICT0112.jpg

Those are some nice looking lipos...:great:

Looks great.

Thanks! Just placed the order for some odds and ends:
Battery trays
Battery straps
CA debonder
Shims
and setscrews

I just thought that I would share my Cen Matrix Buggy conversion (not fancy), but I did read someone (Brushlessboy) here thinking of what CORR Hybrid look would do to it...so here are some PICS.

wow that looks really good! But i have the truggy ;) Where'd you get those piggyback shock caps from?

http://i152.photobucket.com/albums/s...0/PICT0129.jpg
http://i152.photobucket.com/albums/s...0/PICT0130.jpg
http://i152.photobucket.com/albums/s...0/PICT0124.jpg
http://i152.photobucket.com/albums/s...0/PICT0126.jpg
http://i152.photobucket.com/albums/s...0/PICT0131.jpg

The caps were the caps from the CEN GENESIS, and a hardware kit. I got the numbers from CEN SUPPORT. I do not still have the email from them as reference. (I should keep that stuff)

Were they a direct fit for the matrix?

My Matrix Buggy has now the new MEdusa 70mm 2300kV motor, its pretty amazingly better than the china motors. :D

Tests on track: (posted on medusa thread too)

Configs on MMM:
http://xs135.xs.to/xs135/09016/konffit210.jpg

Data:
http://jesi.5cyl.net/RC/tmp/jezze/ampvolt.JPG
http://jesi.5cyl.net/RC/tmp/jezze/watti.JPG

The average amp ~10A was surprisingly low imo, and the peak amp of less than 90A too. So with a Zippy 4s 5000mAh lipo I get at least 20min run time on the track. Maybe even 30min.

Yes. It was direct, and easy. As a bonus even the plastic was the same color. Makes it look factory.

I found the part numbers:

Resivoir: (2) GS233
Small Parts: (1) GS065

Nice tires Ben, the wing looks good to, I got hole shots on my revo.

Looking good dude. Why not set up the truck for saddle packs?

I plan to set up for saddles. I ordered a smaller spur so I can flip the diff and put the motor up front-across from the servo. I have a second set of the losi Trays on the way (the flat bottomed onefits but the other does not) so when all the stuff arrives it will be saddled. I just need to find a place to put the Bigass MMM now...:lol:

Here is what I did when I ran saddle packs (if it helps at all)

http://i160.photobucket.com/albums/t...1231199273.jpg

Different angle:

http://i160.photobucket.com/albums/t...1226883943.jpg

Yeah matrix is a bit different, no chassis brace that blocks the lipo's, and its alot longer so i can get packs in there nice :)

The lipos are the size of a standard 6c pack so im probably gonna lay them down on the chassis... still need to find where im gonna put the MMM

Will you still have room to stick it behind the motor? I say get creative if that doesn't work. Ive mounted rx's and esc's everywhere. Places include in the front bumper, above the wing, below the wing, and the oddest places above motors and servos. You can't just mount a mmm anywhere, but I'm sure you'll find a spot.

:lol:

:lol::rofl:

You're both pushing 3000 now. This was the second post of this thread.

A little off topic but oh well.:party:

I will beat you, Ben.

Not kidding.

Getting there.

I like tacos. Do you like tacos? I like taco bell tacos. I also like meximelts.

My dad calls taco bell toxic belch. I find it funny. Do you?

:lol:
:lol:
:lol:
:lol:
:lol:
:lol:
:lol:
:lol:

:lol:
:lol:
ABC

BREEEEEEEEEEEEEEOOOOOOOOOOPPPPPPPPPPPPPPPPPPPP.
SCOOBA. Flap. :smile: :smile: :smile: :smile: :smile: :smile:

Sizzurp. :rules: :yipi: :angel: :lol::na: :na::na:

Almost there. This is intense. :whistle: :whistle::whistle:
Smileys take the pain out of it,.

i think i wont use any caps or puncuation for this post
yeah this is good
im typing like ben
hahahhaha

Motor is being moved up front.


saddled lipos..



ian- crawl back in your hole:lol:

If I try really hard I might...still lose.:lol:

same with this one
wow
wow
wow
ben
you are
losing
to me
and everyone that has ever
broken 3000 posts

YEAH ALL CAPS NOW. YEAH. YEAH. !!!!!!!!!!!!!!!!!!!!!!!!l!!!!!!!!!!!!!!!

Stop spamming the thread..