Finnally got e-maxx running with MMM on 5s LiPo!!!
 

I have waited about a full year for this, and now, here it is:

http://www.youtube.com/watch?v=oyHOmC_Nal8

better footage will come as soon as i find the pinion and get some daylight!!

Nice. Congrats!

hehe, nailed throttle in basement and this is what happened:

http://i44.tinypic.com/2evye79.jpg

Stripped????

That's what i thought at first but no, i just didn't have the lock nut on all the way.:lol:

Hahahhaha! :rofl: Well that's a relief! Just hope it doesn't happen on the street some day. You'll never find the nut, and, depending on how fast you're going when it happens, you wont find the wheel either. :oh:

I think I'm going to add this on Gee's tips thread:

"Ensure tire locknuts are tight prior to operating your vehicle" :rofl::rofl:.

:rofl: Oddly enough, it's a great tip.

:rofl: yea, that is a very good tip!! lol

yea, when i drove my t-maxx 4 years ago (before the car came with lock nuts) i had a tire to fly off and it went flying down my nabors backyeard downhill and into the woods. it took me forever to find the stupid thing and i never did find the nut

Congrats! Looks like the table got the the worst of that one ;)

.dk

just remounted electronics and batt so it won't glitch as much and so it'd look better! Looks good now!

Hehe, Told yah bro! It working good now though?

And yes, always check nuts are fully fastened before a run:lol::diablo::oh:

haha thanks! I'm about to go take the nuts off and put them back on with threadlocker:mdr:

And idk how well it's working now, i just got it done and it's dark outside :no: But tomarrow we should get some better video and see how everything does!

So far i've been taking it easy running it but temps have been just a little above room temperature with the hottest temp being 86 lol

sweet dude. Sooner or later, lock nuts arnt gonna do it for ya. Your gonna have to get a better looking, better endurance, and bigger things to fit your need....things being rims......17mm is the way to go:lol:

yea i know. i'm going to get some new tires soon becouse these stock tires are very sad.......the car does burnouts half the time:lol:and yet it's a monster truck???? lol sad........ when i got new tires, i'll get new rims with 17mm hexes too.

Got some pics!!!!

http://i40.tinypic.com/2ike6bo.jpg
http://i44.tinypic.com/s5waqh.jpg
http://i41.tinypic.com/aoomlz.jpg
http://i41.tinypic.com/4lrjip.jpg

i'll have some more in a sec!

More pics!!

http://i44.tinypic.com/2qsasg1.jpg
http://i44.tinypic.com/imttfm.jpg
http://i42.tinypic.com/2gy242f.jpg
http://i40.tinypic.com/2pzciyx.jpg

looks a lot better now doesn't it??
I now have a car to be prowd of!! lol

nice built:yes:and i want the exact same motor for my e-maxx..can't wait to buy one:whistle:what is your temp on your motor for your average runtime

My temps have been very low but that's becouse i've only gotten half a charge threw it at a single time and i've only driven it at night so far so i haven't been able to really open it up for a wile yet.

http://i44.tinypic.com/2mnhhrk.jpg
http://i42.tinypic.com/fmqclu.jpg
http://i40.tinypic.com/2mn4ntf.jpg

and i ran it front wheel drive for a wile and this is the temp reading i got from the axle:

http://i42.tinypic.com/4r4ux4.jpg

Got it fixed and drove it some more! lol Now 2 more things broke and my wheelie bar bent lol

http://i40.tinypic.com/34e439w.jpg
http://i43.tinypic.com/205yx5d.jpg
http://i40.tinypic.com/294kvnl.jpg

i'm kinda suprized it broke the driveshaft

looks like it doing well for you. good power.
phil

yea, maybe too much power for it's own good in a maxx. So what's the update with you?

just got a new E-revo. ordered my lipo's and balancer. need a Bl system now and be ready,then will need upgraded radio later.
phil

Did you add the screen mesh over the second servo hole? It looks clean.

Nice! Good luck!!

yea, that was me way of mounting the antena lol

Nice build!

Thanks!

new video:

http://www.youtube.com/watch?v=o9D4uWcqDww

still not much of a video tho. But i made the whole video on my cell phone soo....