Supermaxx brushless
 

Here are some pics from my Supermaxx with brushless setup.

Hope you like it.

http://i68.photobucket.com/albums/i33/VWT4/DSCN7551.jpg

http://i68.photobucket.com/albums/i33/VWT4/DSCN7544.jpg

http://i68.photobucket.com/albums/i33/VWT4/DSCN7539.jpg

http://i68.photobucket.com/albums/i33/VWT4/DSCN7542.jpg

http://i68.photobucket.com/albums/i33/VWT4/DSCN7556.jpg

Cheers.

SUPER NICE MAXX!!
Even the motor plate is perfectly polished.
You sure got me jealous, dude.
How's the truck's speed?

I will measure the speed this weekend with a speed gun.

The R/C Vehicle Speed Calculator throws 42MPH (66km/h), is not too much but I expect tons of torque!!!

Very nice, why do you have a LVC? Got some Lipos on it yet? :)

How did you polish your mount?

Yes, I have 4 Hyperion 3.700mA VX, two 2S and two 3S.

I use it 2S +3S serial wired, total 5S. The discharge is 74A and work great.

The NiMHs are 8 cells side by side packs, two 4K (maxamps), two GP 3.300, and 4 Intellect 3.800ma (two of them matched).

I bought the motor mount and a beautiful transmision case already polished, but the case don't fits in the Lightning chassis :007:

http://i68.photobucket.com/albums/i3.../alutranny.jpg

nice VBS towered...very nice truck indeed

Thanks Shayne.

I have an awesome Ultramaxxed Gen III set in the truck ;-)

I bet you do, and glad you like them Vincent....right now im building a Bl gmaxx.....if you go here you can see a few pics of it that i posted of how my fans are mounted....
http://www.rc-monster.com/forum/show...0800#post70800

bro thats a great looking truck you have.. can you post a pic of what exactly you are using to mount the esc? thanx or anyone that uses something on a e-maxx tranny where the extra motor used to be.

phil

What make is the transmission ? FLM? How doesn't it fit? I have the Lightning with singlespeed, thinking of getting the FLM half-case for full alluminium tranny.

That's a great idea!!

It is the RC-Solutions brushless controller mount, it is in ebay for $8:

https://ssl9.secure-svr.com/rc-solut...1_19_58_17.jpg
http://cgi.ebay.com/RC-Solutions-Tra...QQcmdZViewItem

But Mike sells a better plate that includes heatsink and looks great:

http://i68.photobucket.com/albums/i3...uark20cont.jpg

I think it is Integy, sure it's not FLM. Mine measures only -3mm more than the chassis space between the braces.

That transmission is a GPM.

Is that the horror controller you are using?

Nice truck!!

sweet man! looks really good

Bye:018:

The wabash rimms don't give you the maximum steering. The where limiting my racer-x..

I know alot of people don't like schulze esc's but I had one ran it hard and never had a prob. but I guess people have differant luck.. I had a 18.97 in an E-maxx..
phil

It's not about the quality of the controller, it's the quality (or lack) of service...

That is nice. I like it.

Hallo!

Why doesn´t the case fit in the lightning chassis?

I have the same transmission case and want to install it the next days into my lightning chassis... where´s the problem?

The case is the exact dimension the original emaxx case has...

Marc.

Serum , when I wrote the post I already knew you love Schulze stuff LOL


Marc, mine is only a little wider than the space between the lower braces:

--stock case is 44,45mm

--aluminium case is 44,50mm

If the FLM case fits I will sell the GPM and get the correct one.

Vicente.

that .05mm can't hurt that bad..

You can use a gasket between the two halves, i know Ryan used it for his.

I don't understand you.

Adding a gasket between the halves won't change the width of the case, only the length will increase.

BTW .05mm metal to metal conntact didn't let me fit the case.

So if you drilled out the holes of the chassis with .1 it would be ready to go. not too hard imo.

Hi !

I know what you mean, i tried to install the gear box this night and no, it does not fit.

I am going to buy a milling cutter for my dremel today and cut out the
missing 0,5mm from the braces.

That will not hurt the stability...

Marc.

Hi !

I think you are refering to the transmission half cases that don´t fit quite well because they are too short.

You can either use a gasket or dremel a little bit on the input shaft...

I did the second.

Marc.

I think I would use a file first. The dremel is good for larger amounts.
The file is a safer more even cut.

Since it's only .05 mm, a drill which is .1 larger in diameter should solve the problem without leaving any traces.

Is it the inside of the stuff or the hole?

The way i read it, was that the trans. case was too wide not a hole alignment problem

my reader must be down at this moment..

Here is a short video.

The SuperBigMaxx doing backflips .... you can do all those that you want, one after another one. Absolutely no cogging.

http://i68.photobucket.com/albums/i3..._Backflips.jpg

I really love my 18.149 + Big Pletty combo :004:

That's cool! Most people just talk about them, but they never want to show it! Great Job, looks like tons of torque!

No wonder you don't notice any cogging.. LOL that's an on-off switch, not a controller..

Looks like you geared it pretty high. Cool looking vid!

HOLY CRAP.. it looks like thatq thing FLIES, could u get a slower one so that i can actually see if it isnt touching the ground.

Thats a nice maxx. How much did it dig into your wallet?

It is very easy: pulling the trigger as fast as you can. My 8 years old son loves backfliping, too. :013:

The ratio is 18:1 .

I will try it but I have very little skills editing video. :007:

:dft008:

That is just silly...:p That must be why I like it so much!:027:

Nice truck and killer trick!!!

Here is a very nice video edited by my friend potreinas.

Sorry, the texts are in spanish.


Edited: too much downloads, I had to change to a free host :(

http://www.yourfilehost.com/media.ph..._Potreinas.wmv

sweet vid man....and well done too

Wow that truck is awesome...

OH! :027:
I got you now. :017: