RC-Monster Forums

RC-Monster Forums (https://www.rc-monster.com/forum/index.php)
-   Brushless (https://www.rc-monster.com/forum/forumdisplay.php?f=12)
-   -   Guys I need help! (https://www.rc-monster.com/forum/showthread.php?t=28295)

magman 10.12.2010 09:17 PM

Guys I need help!
 
I just finished my Mugen MRX-3 BL conversion and I am having a serious issue. On the bench it winds up quite nicely, but, once on the ground it barely moves. The motor direction is right, the end points on the radio is maxed out, I trippled checked the esc settings...I am at a loss. I did move the spektrum rx to this car from another car but all I did was change model info on radio so that should not matter.

The car rolls freely on the ground with out power being applied. Any ideas would be helpful

Set up:

2 5K Zippy 25C 3S packs in series for 6S
1518 1800kv It is all I had to test with...a 2600kv will go in later
Spektrum 3S

MMM esc settings:
low start power
70% punch
70% brake
10% drag brake
0 timing
3.3v cutoff
Reverse lock out

Finnster 10.12.2010 09:30 PM

I once fried a LMT and it would behave like that. This is a new motor tho? IDK, are you sure everything works correctly separately?

Arct1k 10.12.2010 09:35 PM

Connections...

magman 10.12.2010 09:43 PM

I will go back and recheck them tomorrow..thanks. Yes the motor is brand new

magman 10.12.2010 09:44 PM

Quote:

Originally Posted by Finnster (Post 383623)
I once fried a LMT and it would behave like that. This is a new motor tho? IDK, are you sure everything works correctly separately?


Yes everything worked before installing into car

What's_nitro? 10.12.2010 10:00 PM

Quote:

Originally Posted by Arct1k (Post 383624)
Connections...

Yeah sounds like a faulty plug somewhere. :yes:

magman 10.12.2010 10:07 PM

Well. I reconnected it to castle link did an update and it goes like the wind...however, when I pull the trigger now it crawls along for 3 seconds and then...WOW it takes off like a rocket w/out warning. Trying to figure out how to get rid of the delay..any ideas

What's_nitro? 10.12.2010 10:09 PM

Did you recalibrate the radio after the update?

magman 10.12.2010 10:11 PM

Quote:

Originally Posted by What's_nitro? (Post 383630)
Did you recalibrate the radio after the update?


what would I calibrate on the DX3s? I have gone over and over the radio looking for some way to get rid of the lag in throttle response

What's_nitro? 10.12.2010 10:34 PM

Errr, to the MMM, I meant. Endpoint calibration... Sorry... :oops:

bdebde 10.12.2010 10:47 PM

Recalibrate the ESC to the radio as if it were a new ESC (full throttle, brake, neutral).

magman 10.13.2010 06:03 AM

Quote:

Originally Posted by bdebde (Post 383638)
Recalibrate the ESC to the radio as if it were a new ESC (full throttle, brake, neutral).

I will try that tonight...thanks

magman 10.13.2010 06:38 AM

I believe I figured it out...after looking through someone else's on road build I realize I forgot to JB weld the spur to the shaft. It slips just enough before it engages. hopefully this will fix the issue

Finnster 10.13.2010 10:30 AM

Quote:

Originally Posted by magman (Post 383671)
I believe I figured it out...after looking through someone else's on road build I realize I forgot to JB weld the spur to the shaft. It slips just enough before it engages. hopefully this will fix the issue

lol..

Funny how the simple things can really trip you up

magman 10.13.2010 11:51 AM

Quote:

Originally Posted by Finnster (Post 383698)
lol..

Funny how the simple things can really trip you up

So true...not only trip you up but drive you crazy until the little light bulb goes off in your head:yes:


All times are GMT -4. The time now is 08:12 PM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2025, vBulletin Solutions Inc.