RC-Monster Forums - View Single Post

timaneli · 12.18.2011, 03:57 PM

i finally finish the conversion and spent no money do it on buying conversion kits or parts.
i made a custom motor mount, a custom battery tray and a custom esc mount.

my goal was to keep things well mount on the chassis and as light as possible.
some pics:

i use a jconcepts illuzion body.

i use a ezrun sc8 combo on single 3s lipo geared at 13/48.

for battery i cut a plate tu put the battery tray without having flexing issues and to keep lipo close to chassis.

for the motor i use a 4 mm´s steel plate.

since ezrun esc is small i was able to put it between front shocks mount and the gearbox.
it was the best place i found since i don´t want a esc stucking over other parts.

for the receiver i use a traxxas stampede 4x4 water proof box and put it on the place of one of the steering servos since i use single servo setup.
i use all stcok screws places to put custom parts and the only holes i done was for the esc mount.
also with this parts location i can upgrade the chassis with front and rear sway bars and i can change or take of any part without having to remove others.
the car is running between 35 and 40 mph and that thank´s to the 2700kv of this 4 pole leopard motor and without anything heat up and i also have center diff that i want to take of because i only bash and this center diff is taking some speed and power from rear wheels to front ones.
i am waiting for e-revo shocks and some aluminiuns plates and that is it for now.
with lipo and ready to run the car weights 9.24 pounds so it is way lighter than a e-revo loaded too.

i had a e-revo on 4s on past but this baby is way better!!
hope you guy´s like and after i spent 3 packs today i just want to bash more and more!!

greetings

	(#6)
timaneli RC-Monster Carbon Fiber Offline Posts: 155 Join Date: Jun 2008	12.18.2011, 03:57 PM i finally finish the conversion and spent no money do it on buying conversion kits or parts. i made a custom motor mount, a custom battery tray and a custom esc mount. my goal was to keep things well mount on the chassis and as light as possible. some pics: i use a jconcepts illuzion body. i use a ezrun sc8 combo on single 3s lipo geared at 13/48. for battery i cut a plate tu put the battery tray without having flexing issues and to keep lipo close to chassis. for the motor i use a 4 mm´s steel plate. since ezrun esc is small i was able to put it between front shocks mount and the gearbox. it was the best place i found since i don´t want a esc stucking over other parts. for the receiver i use a traxxas stampede 4x4 water proof box and put it on the place of one of the steering servos since i use single servo setup. i use all stcok screws places to put custom parts and the only holes i done was for the esc mount. also with this parts location i can upgrade the chassis with front and rear sway bars and i can change or take of any part without having to remove others. the car is running between 35 and 40 mph and that thank´s to the 2700kv of this 4 pole leopard motor and without anything heat up and i also have center diff that i want to take of because i only bash and this center diff is taking some speed and power from rear wheels to front ones. i am waiting for e-revo shocks and some aluminiuns plates and that is it for now. with lipo and ready to run the car weights 9.24 pounds so it is way lighter than a e-revo loaded too. i had a e-revo on 4s on past but this baby is way better!! hope you guy´s like and after i spent 3 packs today i just want to bash more and more!! greetings you are what you race!!