RC-Monster Forums  

Go Back   RC-Monster Forums > Support Forums > Brushless
Reload this Page simple question...

Reply
 
Thread Tools Rate Thread Display Modes
simple question...
Old
  (#1)
fagzz
Guest
 
Posts: n/a
simple question... - 08.26.2006, 10:27 AM
hi guys, i just wondered if i was supposed to recalibrate my 9920 controler to run my new Feigao7XL motor? I ran a 9L before...
Thanks for the help! :032:
   
Reply With Quote
Old
  (#2)
squeeforever
RC-Monster Mod
 
squeeforever's Avatar
 
Offline
Posts: 6,254
Join Date: May 2005
Location: Baton Rouge
08.26.2006, 10:36 AM
Yea. You might want to reprogram it.
  Send a message via AIM to squeeforever  
Reply With Quote
Old
  (#3)
coolhandcountry
RC-Monster Mod
 
coolhandcountry's Avatar
 
Offline
Posts: 6,741
Join Date: Jul 2005
Location: VA in the US
08.27.2006, 09:09 AM
If you running the same radio and truck. I don't see no need. You can though.

Peace!
Country
Help support the
Rc-Monster
Buy here
   
Reply With Quote
Old
  (#4)
fagzz
Guest
 
Posts: n/a
08.27.2006, 02:23 PM
imo if i keep the same tx and rx, there is no need... but i don't want to do bad... therefore i will recalibrate the controler...
tks for all...
   
Reply With Quote
Old
  (#5)
fagzz
Guest
 
Posts: n/a
08.27.2006, 04:01 PM
does the calibration consider only TX EPAs??? or does it measure the motor parameters???
   
Reply With Quote
Old
  (#6)
MetalMan
RC-Monster Mod
 
MetalMan's Avatar
 
Offline
Posts: 5,297
Join Date: Mar 2005
Location: SoCal
08.27.2006, 11:23 PM
Calibration only uses the TX EPA.

SH Z-Car, Custom Crawler, 8s Savage, 12s XTM XLB 1/7 buggy, 4wd 4-link rear/IFS Pro4 truck, Custom Hyper 10 Short Course, Belt-Drive Mammoth ST 1/8 truggy, 4s 17.5 MM Pro HPI Blitz
   
Reply With Quote
Old
  (#7)
fagzz
Guest
 
Posts: n/a
08.28.2006, 04:23 AM
therefore there is no need to recalibrate my BK9920 controler to run another motor on it? that's not clear...
   
Reply With Quote
Old
  (#8)
coolhandcountry
RC-Monster Mod
 
coolhandcountry's Avatar
 
Offline
Posts: 6,741
Join Date: Jul 2005
Location: VA in the US
08.28.2006, 08:05 AM
When you calabrate the esc. It only reads the tx (radio transmitter). It don't read nothing from motor side.

Peace!
Country
Help support the
Rc-Monster
Buy here
   
Reply With Quote
Reply

« Previous Thread | Next Thread »

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Forum Jump







Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2025, vBulletin Solutions Inc.
vBulletin Skin developed by: vBStyles.com

Contact Us - RC-Monster Store - Archive - Top