 |
|
|
|
|
|
 |
|
|
 |
Can't calibrate DX3R/DSM2 combo with Mamba Monster |
 |
|
 |
|
(#1)
|
|
Guest
Posts: n/a
|
Can't calibrate DX3R/DSM2 combo with Mamba Monster -
03.20.2010, 01:19 AM
Strange things happening. DX3R binds with either DSM2 or DSM1 receiver. BUT when i try to calibrate with MM it does forward ok, then reverse ok, then will eventually do neutral after a longer peiod of time than normal!
The ESC then arms, but goes nuts, just like a run-a-way AM... no way to control it ! My old DX3 binds with the DSM1, calibrates ok, then ESC arms and works well :-) I know the DX3R is ok, because I use it on another model with similiar specs ! Anybody run into similiar problems? |
|
|
|
 |
 |
 |
|
|
|
|
|
|
(#2)
|
|
i pwn nitro
Offline
Posts: 769
Join Date: Nov 2008
Location: with ur GF
|
03.20.2010, 01:25 AM
well actually, i did get it to calibrate neutral but when the ESC armed it went absolutely mad!! full forward, full reverse, full forward.
might i also add that the servo was also playing up (full left, full right). but not with DSM1 operation. even when a DSM1 receiver was used with a DSM2 transmitter. the porthole from the noob world an here has been opened!! that's how i got in. |
 |
|
|
|
|
|
|
|
|
|
|
(#3)
|
|
Guest
Posts: n/a
|
03.20.2010, 04:49 AM
I've have similar issues with Mamba Max / Spektrum DX3S combo
Only way to get it to calibrate was to rollback the esc firmware Castle are apprently looking at it there is an old thread discussing it here http://www.rc-monster.com/forum/showthread.php?t=24984 Cheers |
|
|
|
|
|
|
|
|
|
|
|
|
(#4)
|
|
Guest
Posts: n/a
|
03.20.2010, 05:36 AM
Thanks, crusey_aus,
That is exactly my problem.. couldn't find it on the forums... but thanks again. :-) |
|
|
|
|
|
|
|
|
|
|
|
|
(#5)
|
|
Guest
Posts: n/a
|
03.20.2010, 06:10 AM
Tried reverting to firmware V1.20... but same problem occuring... binds OK, calibration does fwd & reverse OK... but strange things still happen when calibrating the neutral position...
|
|
|
|
|
|
|
|
|
|
|
|
|
(#6)
|
|
RC-Monster Dual Brushless
Offline
Posts: 4,236
Join Date: Dec 2007
Location: Cape Cod, Mass.
|
03.20.2010, 08:49 AM
That is odd..I have a 3S and mmm w/newest firmware and had no issues. followed directions to a tee and done..
2. MBX-5T 1520, MMM ON 5S 3. MBX-5 ONROAD CONVERSION 1515, MMM ON 5S 4. MRX-3 ON ROAD CONVERSION 1512, MMM ON 6S 5. TEN T 2650 T8, MMP ON 3S |
|
|
|
|
|
|
|
|
|
|
|
|
(#7)
|
|
Guest
Posts: n/a
|
03.20.2010, 09:24 AM
I have 3 different MMM systems all running off the same DX3S and had no trouble binding or calibrating them . Check too see that all the trims are at zero before you try too calibrate .
|
|
|
|
|
|
|
|
|
|
|
|
|
(#8)
|
|
RC-Monster RC8T
Offline
Posts: 2,554
Join Date: Jan 2008
Location: Syracuse, New York (Camillus)
|
03.20.2010, 03:46 PM
May be the rx
SC10 MMPro 13.5T 2s NeuEnery 5000mah RC18T Mamba 25/5400kv 2s lipo + 6s NiMh |
|
|
|
|
|
|
|
|
|
|
|
|
(#9)
|
|
Guest
Posts: n/a
|
03.20.2010, 04:12 PM
Checked all trims were zeroed at time of calibration. The problem is there ONLY with the DX3R with either the DSM1 or DSM2 rx. Problem NOT there with the DSM1 and plain DX3.
Racing a little later on this morning, so don't wanna stuff around with it anymore today. Will tinker when I get home this afternoon :-) |
|
|
|
|
|
|
|
|
|
|
|
|
(#10)
|
|
RC-Monster Aluminum
Offline
Posts: 704
Join Date: May 2008
|
03.21.2010, 11:45 PM
Seems to be an issue on radios that use a faster frame rate. Had no issues on a DX2, DX3, DX3E or DX3S but a DX3R and a KO EX-5UR all needed the ESC to go back to V1.20 firmware to calibrate.
|
|
|
|
|
|
|
 |
«
Previous Thread
|
Next Thread
»
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
Hybrid Mode
|
|
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2025, vBulletin Solutions Inc.
vBulletin Skin developed by: vBStyles.com
Copyright ©2000 - 2025, vBulletin Solutions Inc.
vBulletin Skin developed by: vBStyles.com
