RC-Monster Forums  

Go Back   RC-Monster Forums > Support Forums > Castle Creations

Reply
 
Thread Tools Rate Thread Display Modes
Old
  (#1)
rchippie
RC-Monster Brushless
 
rchippie's Avatar
 
Offline
Posts: 2,824
Join Date: Apr 2005
Location: largo fl
01.19.2007, 10:10 PM

I think the fan breaking was a factor. As for motor i forgot to check.


What do you think about the speedo cutting off after a little bit of running. I think it has to do with the UBEC because i had no steering when it cut off. Then maybe 3-4 seconds max it would start back up & run for a while.


REAL MEN RUN BRUSHLESS

Last edited by rchippie; 01.19.2007 at 10:21 PM.
   
Reply With Quote
Old
  (#2)
BrianG
RC-Monster Admin
 
BrianG's Avatar
 
Offline
Posts: 14,609
Join Date: Nov 2005
Location: Des Moines, IA
01.19.2007, 10:32 PM

Well, if your BEC is cutting out for whatever reason, it will affect steering and throttle. The ESC gets the throttle signal from the receiver and if the receiver loses power, then there goes the signal. Who knows, the BEC could have a bad solder joint, not rated for the current the servo and fan needs, etc. You can always try a receiver pack to verify that it's the BEC.
  Send a message via Yahoo to BrianG Send a message via MSN to BrianG  
Reply With Quote
Old
  (#3)
rchippie
RC-Monster Brushless
 
rchippie's Avatar
 
Offline
Posts: 2,824
Join Date: Apr 2005
Location: largo fl
01.19.2007, 10:43 PM

I plan on trying a reciver pack on my next outing When i had my BL mbx4 i used a reciver pack with no issues. I'm hoping the UBEC is the reaon for it cutting out.

Also i just reprogramed my speedo. I lowerd the timing from normal to LOW & start power to low.


REAL MEN RUN BRUSHLESS

Last edited by rchippie; 01.19.2007 at 10:48 PM.
   
Reply With Quote
Old
  (#4)
BrianG
RC-Monster Admin
 
BrianG's Avatar
 
Offline
Posts: 14,609
Join Date: Nov 2005
Location: Des Moines, IA
01.19.2007, 10:46 PM

What BEC are you using? Sometimes a properly sized capacitor can help a lot to even out the bec voltage, smooth out current pulses, and filters any noise from the bec output...
  Send a message via Yahoo to BrianG Send a message via MSN to BrianG  
Reply With Quote
Old
  (#5)
rchippie
RC-Monster Brushless
 
rchippie's Avatar
 
Offline
Posts: 2,824
Join Date: Apr 2005
Location: largo fl
01.19.2007, 10:50 PM

Im using a UBEC that i bought from mike.


REAL MEN RUN BRUSHLESS
   
Reply With Quote
Old
  (#6)
BrianG
RC-Monster Admin
 
BrianG's Avatar
 
Offline
Posts: 14,609
Join Date: Nov 2005
Location: Des Moines, IA
01.19.2007, 10:54 PM

It's kinda rare, but I've heard a couple people have a problem with them. Could be a loose solder joint or something equally simple.
  Send a message via Yahoo to BrianG Send a message via MSN to BrianG  
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump







Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2025, vBulletin Solutions Inc.
vBulletin Skin developed by: vBStyles.com