RC-Monster Forums  

Go Back   RC-Monster Forums > Support Forums > Brushless

Reply
 
Thread Tools Rate Thread Display Modes
Help getting emaxx working
Old
  (#1)
makana59
RC-Monster Carbon Fiber
 
makana59's Avatar
 
Offline
Posts: 93
Join Date: Dec 2005
Location: Hawaii
Help getting emaxx working - 08.18.2008, 09:18 PM

Im just trying to get the emaxx running again. Its been about 1 1/2 years since the last runs and Im pretty sure the battereies are shoot. I just have a few questions if you can help me with about getting her going again. First of all I have a emaxx with a feigao motor, bk warrior 9920 controller, UBEC, Blue bird servo, and stock receiver. I stopped the last time playing with her becuase the controller started to overheat and smoke. I dont know if the controller was bad? the UBEC was bad, I just dont really know why. then the emaxx would stutter when I apply gas on the trigger control.

So basically with all the new setups and equipment now days what would be some of your recommendations to get her going again. I basically want her fast and long lasting. I dont bash too hard. Just at the parks and streets. No high jumps and stuff. Was wondering if this would be able to go to Lipo batteries. or should I just stick with NiMH? Just need some help to get her going again. Thanks for all the help and taking time to read this long reply. Makana

Last edited by BrianG; 08.18.2008 at 09:22 PM.
   
Reply With Quote
Old
  (#2)
BrianG
RC-Monster Admin
 
BrianG's Avatar
 
Offline
Posts: 14,609
Join Date: Nov 2005
Location: Des Moines, IA
08.18.2008, 09:22 PM

Moved this post to a new thread to keep the FAQ clean of general questions...
  Send a message via Yahoo to BrianG Send a message via MSN to BrianG  
Reply With Quote
Old
  (#3)
E-Revonut
RC-Monster RC8T
 
E-Revonut's Avatar
 
Offline
Posts: 2,554
Join Date: Jan 2008
Location: Syracuse, New York (Camillus)
08.18.2008, 09:42 PM

Well if youy know your esc is smoked you def need a new one. If you've waited this long you might as well order a MMM and wait the couple weeks till you get it. If your motor is good you might as well use it till it isn't or your unhappy with it's performance. Lastly I would have to recomend dumping your NiMh batteries and charger in favor of the much more powerful Lipo batteries and the charger to go with them. Way more power than NiMh, lighter weight, and longer run times. No matter what Lipo batteries you choose they will far out performe your NiMh cells.
   
Reply With Quote
Old
  (#4)
makana59
RC-Monster Carbon Fiber
 
makana59's Avatar
 
Offline
Posts: 93
Join Date: Dec 2005
Location: Hawaii
08.23.2008, 02:41 AM

I guess I need a little help with which controller is pretty good, which motor you would recommend and what lipos is decent also. Is there a link where i can read up about Lipos. I guess its been such a long time Im still stuck in the NiMH age. If you have help i would greatly appreicate it. Ill try to check around in the FAQ section. THanks again, Makana
   
Reply With Quote
Old
  (#5)
E-Revonut
RC-Monster RC8T
 
E-Revonut's Avatar
 
Offline
Posts: 2,554
Join Date: Jan 2008
Location: Syracuse, New York (Camillus)
08.23.2008, 03:29 PM

How big is your budget? I love my Spektrum DX3R radio but that will set you back $300 As for info on Lipos MaxAmps.com has an info section. There Lipos aren't the highest quality but IMO pretty decent for the money. Enerland based cells seem to be all the rage on here, I don't have any though. I've been pretty happy with my Maxamp packs. No matter what Lipo you go with they will blow your mind compared to NiMh packs.
   
Reply With Quote
Old
  (#6)
tc3_racer_001
RC-Monster Carbon FIBRE NOT FIBER!
 
tc3_racer_001's Avatar
 
Offline
Posts: 701
Join Date: Apr 2008
Location: Brisbane, Australia
08.23.2008, 07:42 PM

check out the zippy packs on hobbycity (hong kong site) they are the cheapest and should beat the maxamps packs. (even if they were the same, the cost difference is quite large)
u will probably want 4s (14.8v, comparable to 15-16 nimh)


hyper 8.5 pro SOLD!
Monster Max Still Working...
JR SX3
Neu 1512 2D/S
12t pinion
4800 zippy-r


XRAY xt8
MMM
Neu 1512 3D/F
11t pinion
6s 5000 Flightmax/ 4s 4000 Turningy
  Send a message via MSN to tc3_racer_001  
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump







Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2025, vBulletin Solutions Inc.
vBulletin Skin developed by: vBStyles.com